Language
English
English
Español
RVR TX06KSS/20S42 6.2 KW HOTSWAP PLUG IN SOLID STATE TRANSMITTER
SKU
TX06KSS/20S42
MFR#
TX06KSS/20S42
$41,850.00
Availability:
Out of stock
The PJ10KPS-CA is a RF amplifier for frequency modulation sound broadcasting. It is a fully solid-state apparatus of modern design that uses MOSFET as active components in the FM amplifying modules.
The amplifier is supplied complete with all its parts, not really "modules", essential for its operation such as the fans for dissipating the heat generated by the machine inside the room and all the accessories for the electrical and RF wiring. As a rule, the amplifier is supplied as a complete transmitter therefore the two FM exciters that it manages will be provided and connected (a service exciter and a spare exciter)
Features
- Tunable over entire FM band (87.5 – 108 MHZ), without tuning.
- Overall efficiency better than 70%.
- Hot-pluggable and broadband power amplifier modules.
- Each module features switching mode power supply to control and stabilize power supply voltage.
- Each amplifier module provides Automatic Power Control.
- Suitable for mono & stereo broadcast operations.
- Protection against high VSWR, overdrive, overcurrent and overtemperature.
- Compliance to IEC safety standards.
- Compliance to ETSI – CCIR – FCC standards.
- Entire transmitter can be switched off through an emergency button.
- High redundancy guaranteed by 3 power modules of 2.2 kW RF power.
- All measurement and working parameters are displayed on front panel.
- Remotely controllable by telemetry system.
- Design for 24/7 non-stop operation.
- The transmitter include an integrated system for automatic and manual switching between two exciters.
- In Automatic mode the changeover is activated when active power of exciter falls below 3dB.
Specifications
GENERALS
- RF Output Power: 6,3 kW
- Frequency Rang: 87,5 – 108 MHz
- Frequency Stability: > 1 ppm
- Frequency programmability: By software, with 1, 10, 100 , 1000 kHz steps
- Nominal Frequency Deviation: ±75 KHz (peak)
- Maximum Frequency Deviation: ±150 KHz (peak)
- Class of Emission: 180KF8E Direct to Channel
- Modulation Mode: Mono, Stereo, Multiplex, SCA, RDS, Aux
- Stereo transmissions: Acc. to ITU-R / Rec. 450 (Pilot tone)
- RF Output Impedance: 50 Ω, Unbalanced
- RF Output Connector: 1-5/8” EIA Flange
- VSWR: 1.4:1 with automatic fold-back at higher VSWR
- Pre-emphasis Mode : 0/50 (CCIR) µs,75 (FCC) μs
- Asynchronous AM S/N Ratio: Typically >70dB
- Synchronous AM S/N Ratio: Typically > 55dB
- Harmonics suppression and Spurious: Typically <85db
- Overall efficiency: Typically > 70%
- RF Harmonics: Exceeds ETSI/CCIR/FCC requirements
- RF Spurious: Exceeds ETSI/CCIR/FCC requirements
- Analogue Input level {+75 Khz (peak) deviation }: -12,5 dBu - +12,5 dBu (adjustable)
- Digital Input level {+75 Khz (peak) deviation }: -20,0 dBFS – 0 dBFS (adjustable)
MONO OPERATION
- S/N ratio: Typically > 83dB
- Total Harmonic Distortion + Noise: Typically <0,03%
- Inter Modulation Distortion SMPTE: Typically <0,02%
- Frequency Response: Typically ±0,2dB
- Audio Input Impedance: 600 Ω or 10 kΩ
MPX OPERATION
- Composite S/N ratio: Typically > 80dB
- Total Harmonic Distortion + Noise: Typically <0,05%
- Inter Modulation Distortion: Typically <0,05%
- Frequency Response: Typically ±0,2dB
- Audio Input Impedance: 10 kΩ
STEREO OPERATION
- Stereo FM S/N Ratio: Typically > 83dB
- Total Harmonic Distortion + Noise (L or R): Typically <0,02%
- Inter Modulation Distortion SMPTE (L or R): Typically <0,02%
- Frequency response (L or R): Typically ±0,2dB
- Linear Cross Talk: Typically > 50dB
- Non-linear Cross Talk: Typically > 50dB
- Stereo Separation (Sine Wave): Typically > 70dB
- Audio Input Impedance: 600 Ω or 10 kΩ
- Digital Input Impedance: 110 Ω